Экофлок
Jager_TD90-2-G
Контактная информация
- Email:
- График работы:Пн - Пт: с 09.00 до 18.00Cб - Вс: Выходной
Jäger Umwelt-Technik GmbH
®
JetFlex TD 90-2 G
Dimensions
Material
Tube
ID-Sleeve
Wall
diameter
thickness
(
grooved)
EPDMper-
formance
87 mm
90 mm
90 mm
90 mm
1,9 ± 0,20
mm
Silicon
translucent
87 mm
87 mm
1,5 ± 0,20
mm
Pur trans-
parent
0,75 ± 0,05
mm
ƒ
ƒ
ƒ
Shutdown of operation is highly recommended for air flow
rates lower than minimum rate.
Do not apply overload air flow rate (e.g. cleaning) for more
than 10 minutes each day.
Numbers are for guidance only. Operating diffusers at too
high or too low airflow rate may reduce lifetime or perfor-
mance. See Technical Report `Membrane Fouling Issues´ for
details.
Installation drawing
SSOTE and headloss for EPDM 1000mm
B
C
A
D
A
B
C
Total length
Perforation length
Header
D
Connector
Air Flow Rate Q [m³/h]
Perforation
length [B]
Total length [A]
Perforated area
Air flow rate at standard
operating conditions
Max. overload/
maintenance air flow rate
3
3
1000 mm
1145 mm
895 mm
645 mm
0.24 m²
0.18 m²
0.12 m²
6 - 18 m /h
N
28 m /h
N
3
3
750 mm
4 - 14 m /h
N
21 m /h
N
3
3
5
00 mm
3 - 9 m /h
N
14 m /h
N
Operating temperature air Operating temperature water
- 60 °C 5 - 30 °C
Operating mode
Application
5
continuous / intermittent
municipal waste water
Dimensions for threads and connector
Connector
E]
Pipe thread ISO 228 -G 1A
Connector length
square tube 80 x 80 mm [C] square tube 100 x 100 mm [C]
Connector length
Drill hole for connector
[D]
[
145 mm 165 mm
35 ±1
®
JetFlex TD 90-2 G
Membrane materials
Material
EPDMperfor-
mance
Silicone
PUR
Colour
Polymer
black
33 %
20 %
35 %
12 %
translucent
50 %
transparent
100 %
Carbon black
Plasticiser
0 %
0 %
0 %
0 %
Others
50 %
0 %
Density
DIN EN ISO 1183-1
DIN 53504
1,11 ±0,03 g/m³ 1,16 ±0,03 g/m³
1,18 ±0,03 g/m³
40 MPa
Tensile strength
Elongation at break
Tear strength
Hardness
> 7 MPa
> 400%
> 9 MPa
> 600%
DIN 53504
≥ 600 %
65 N/mm
DIN EN ISO 34-1
> 7,5 N/mm
40 ± 5 Shore A
< 7%
> 20 N/mm
60 ± 5 Shore A
DIN ISO 7619-1
Tension set
Ozone resistance
DIN ISO 2285, 100% Elongation; 24 h, RT
DIN ISO 1431-1 (500ppb)
no cracks
no cracks
no cracks
Other materials
Pipe
Head
Clamp
1.4301
Gasket
Connector
PP
PP 30% GF
EPDM SI
1.4301
2-grooved diffuser
Grooves will evenly distribute air from front to end over years even in
difficult to treat waste water.
Accessories
Air (blue) flows easily
Air is squeezed through
a narrow gap between
sleeve and tube increa-
sing headloss.
through
the
grooves
causing considerable lower
headloss. The circumference
of the grooved tube is equal
to the ID of the membrane.
Stainless-steel
connectors (square
headers)
Adapters
Blind plugs
Ø 40 or Ø 45
Plastic connectors
Sealing for adapters Clamp adapters (round
headers)
/
saddles (round
headers)
Disclaimer
This information is based on our
present state of knowledge and
is intended to provide non-legally
binding general notes on our
products and their uses. It should
not therefore be construed as
guaranteeing specific properties of
the products described or their suita-
bility for a particular application. Any
existing industrial property rights
must be observed. Errors excepted.
We disclaim any liability for infor-
mation contained in this Data Sheet
and for product information. Contact
Jäger Umwelt-Technik GmbH & Co. KG
Ruscheplatenstraße 14
Jaeger Rubber and Plastics (Shenzhen) Ltd.
1/F, No. A9 Factory Building, Silicon Valley –
Automobile Industry Park
Guanlan, Baoan, Shenzhen,
China 518110
+86 755 2983 2412
+86 755 2983 2413
www.jaeger-shenzhen.cn
info@jaeger-shenzhen.cn
31137 Hildesheim
Germany
+
+
49 5121 9138 900
49 5121 9138 999
Jaeger for a detailed lay-out &
design for your individual plant.
www.jaeger-envirotech.com
info@jaeger-envirotech.com
Jager_TD90-2-G
Получить бесплатную консультацию
Для получения более детальной информацией свяжитесь с нами
или оставьте свои контактные данные и мы обязательно Вам перезвоним.